Wednesday, 21 September 2016

Massey 2cwt "with-slides" Power Hammer Restoration, "BESSIE"



Early in July 2015, I received a phone call from John Nicholson at Massey in Manchester advising me that he had heard of a machine that had become available in Norfolk (about 90mins drive from me). it was fairly well known among the community that I had been looking for a machine for some time (even looking as afar abroad as Malaysia to repatriate a beautiful Alldays and Onion 1cwt,Germany for a Beche L4 also, Italy and France for other opportunities. the reason for all of these instances not coming into fruition being the exorbitant cost of transport [particularly the Malay example,  as there are additional cost when something has to pass through port]) 



These machines are becoming increasingly  rare with a dwindling numbers  in existence thanks due to the "scrap everything" policy of Administrators when a business goes into liquidation-our sector in particular as many of the light and medium forging companies used to fairly large employers of with numerous pieces of forging equipment under one roof. When those business fell through in the 70's 80's & 90's alot of machinery was lost overnight. 


So there's that, but then there is also the fact that in the current climate of their scarcity, those who have these machines tend to hold on to them (I know I will!).  This all adds up to make their availability increasingly limited. 

So! With this in mind I was excited and surprised to hear of a piece of equipment  that was available and so close.  

The piece was being sold by a certain Mr Bill Corduroy- a well known name in the British blacksmith crowd (In fact a real bonus prize that this hammer was being sold by Bill was that I got to meet Bill who is hands down one of the nicest people I have met). 

I made travel arrangements and went to view the hammer and bought it right away. 




This is the situation it was in- Bill had bought this hammer  about 25 years ago with the intention of "putting it in" but the enormity of that task coupled with his busy, successful career meant that he simply never got around to it. It is often said these days that power hammers tend to be owned by two or three persons before someone actually installs it. They tend to become a "feature" in what is known as "Yard Art". 

The had been standing here for about 25 years and Bill though it had not run for a while when he bought it from an industrial smithy- so lets call it 30 years.  It had, however been under cover for all that time and greased somewhat  when put away. The grease will prevent the majority of water ingress, but it has the surprising effect of becoming quite adhesive when left to oxidise for years- effectively gluing the system together. 



After speaking to another staple of Norfolk blacksmith, Nigel Barnett of Fransham forge (who has a alot of experience moving big heavy things around) I got the number of a guy with a flat bed and hiab and we got the old girl delivered to Leicestershire






Spending the money is the easy part, now came the real work.  I had zero movement in the fly wheel when pushing by hand so i had to take the cylinder covers off to have a look at what was going on inside.

The fly wheel is attached to the compressor cylinder by a large con-rod, so that when the wheel makes one rotation the compressor cylinder has made one full stroke- up and down, once.


I removed the cover on the compressor cylinder- as you can see I found quite a lot of well developed crusty rust. People tend to think of rust as soft, powdery  or brittle but when you have two well fitting surfaces next to one another and a film of corrosion, what you actually have is an incredibly strong adhesive.  In a components such as a large piston and cylinder these forces combined to make something fairly immutable.


I was glad that part of the cylinder was exposed as this offered me a "way in" - if the compressor had been all the way up to the top it would have been harder to clean and get back to free movement.  The best way to proceed was scrape clean all the exposed parts I could get into so I could begin to feed cylinder with penetrating oils and fluids (quite a lot of diesel went through it too which has quite impressive rust easing capabilities).


At this point I moved on to the hammer cylinder itself, which we discovered was pretty clean and after an arbitrary wipe out with a cloth, we decided to jack up the hammer head to see if we had movement- which we did. So we put an inch of machine oil at the bottom of the cylinder and moved on.



Its important to understand that these images are slightly out of sequence and that the amount of time taken on the project has thus far not been addressed.  Truth is, that i have too many images of the job for it to be interesting- I could have included before, during and after photographs of every single element but I feel that would in all likelihood become a bit boring for all but the most ardent machine enthusiasts. Also, many of the components are internal so the before shots would illustrate very little, other than the component being stuck inside.


A good example of this is the Valve, which spent over two weeks being fed with oil and gentle pressure before becoming unstuck.

This is the valve,  which in my Massey is the later "vertical type" (as opposed to the earlier models which had a simpler "horizontal" valve, which is much more common feature of power hammers across many different brands such as Alldays and Pilkington). The valve is about 30" long and comprised of multiple free- spinning disks some of which has small springs to maintain a seal. The disks are not symmetrical or repeating and as such their order of assembly was crucial. These disk all assemble over a central rod which is threaded at both end in  order to keep the piece together.  additionally, the disks are cast iron and as such, brittle.

This component was again totally fused together with corrosion which you can see in the image as the wet (oil) gritty material. It should be noted that this is only about 1.3 of the valve as the rest of it at this point was still contained within the valve cylinder.  I was lucky that despite the surface corrosion, that my valve assembly need little work other than cleaning.


I spent alot of time up here.

Sometimes there were ducks...



I got a friend to blast the most of the grime and paint of which was quite spectacular- i had not realised just how loud grit blasting was until that point.



We had covered all of the vent and access point up as best we could to make sure as little grit got in as possible.




Once she was naked I put some red oxide primer on which dried to a rather attractive salmon pink.






It was only after several weeks that I had managed to get enough movement on the piston to remove it and address the rust frozen piston rings, which need to be free spinning and able to expand. Again I was lucky that none of these needed swapping as they were all in good condition.

I will just explain how  I got the compressor cylinder free as it may be of use to someone in a similar position.

Because the cylinder covers are built to take the pressure of the machine in action- they are strong, this is your advantage. Refer back to the previous image of the piston when it was first exposed, there was a gap of about three inches between the top of the piston and the top of the cylinder. What you need to do is fill the cylinder with some kind of rust penetrating fluid, as mentioned before. Then use a large piece of timber that is thicker than the gap (in this case 3" gap = 4" timber packer) and place the timber packer on top of the stuck piston and then return the cylinder cover plate to where it should be, attach all of the bolts and carefully ratchet them all down so the cylinder cap is applying the pressure in a radial fashion. keep going round the bolts giving  a little tighten to each of them until the cover plate has gone all the way down. if you then take the plate off and add additional packers you will eventually force the piston all the way down to the bottom giving you free access to clean the cylinder. Oil it and try to manually push the piston back up using the fly wheel - if this works and you have movement (even slow stiff movement) then you are winning.  push the piston back up and prop it in place so that you can clean the cylinder behind it.

It not impossible that this method won't work and that your piston will remain stuck in position, but it should be tried first if you have a piston that is stuck or seized.  Other methods which work are to apply heat with small fires or heat guns- you do this at your own risk. I personally don't know anyone who has cracked a cylinder doing this, but it is possible. I would suggest however that if your power hammer cylinder cracks after lighting a paper fire in it- then it was probably junk anyway.  Also a cracked cylinder is not worth repairing in most cases unless you have facility fully testing a repair up to industry standards. I have first hand accounts of some of the largest industrial smithies having hammers with repaired cylinders exploding and killing operators. 



At this point I had a machine which was mechanically ok (as best as I could evaluate) So it was time for me to proceed on to the ground work. Which was utterly exhausting.  I had told myself to hire a mini digger and smash the job just as quickly as possible. Brilliant advice that I soundly ignored.

Instead, I decided that I would just "have a go by hand and see how it goes". I think at this point I was trying to save a few pennies. I prepared the area for the ground work and cut the perimeter with a floorsaw and the then cut then interior into 12" squares. At the corner of each square I drilled right through with a sds 20mm bit. When that was all done I thought -"that's probably enough- I will have compromised it for sure!". So, with full confidence I lifted the 24lb sledge we keep for just such emergencies right above my head and brought it fully down to the middle of the well--perforated crisscross.

No effect. I tried again and again for half an hour hitting the same position (the centre-where I assumed to be "weakest") and the floor of the workshop just laughed at me. it was a tthis point i phoned the tool hire people and got kango floor breaker in which was, frankly miraculous, but still incredibly exhausting to use!  When I eventually found my way through the concrete (which turned out to be a bit more than 8" thick, with steel re-enforcement) and exposed the earth underneath, things became a little easier as you are suddenly able to nibble away at the edge of the whole you've made. The added bonus then is that the tip of the breaker goes very easily into the soil, becoming stuck each time.
After I had cleared away the one ton of concrete floor rubble, it was time to start excavating. It was at this point I should have got a digger in as the sub solid turned out to be pure red and blue clay ( no actual soil whatsoever) with large granite stones throughout. It was very difficult going as the clay totally absorbed the impact of the spade making it very hard to pick up any meaningful amount at one time.




My brother stopped by for some encouragement- I was about dead by this point.


Despite being hard  going it did make a beautiful hole! 



The bottom was filled and leveled with sieved hard core. Large ply wood board onto this, then alternating layers of cork board and dense conveyor belt rubber matting. this was an ad-hoc solution to isolate the vibrations. proper fabreeka matting would have a few grand and was not called for given my location.
on top of this we built a water tight board container, and isolated this from its surroundings with 50mm polystyrene.  We fabricated the cage that held the floor bolts and the recess for the anvil and lowered this in place.  This was welded in situ to prevent movement during the concrete pour- the bottom of the anvil recess was removable to allow for removal of air bubbles. 



two pack self levelling floor compound poured onto the raw concrete.  and ready for the machine movers! 





Some more paint




Three musketeers.




After all that I spose I should show you what she does.






After all that I spose I should show you what she does. 

The dates on the photographs tell me how long it took. 

The first image when I just met her for the first time is the 7th of July 2015 and the first image I have of her running the first time is 15th December  so that is five months of work and organising others. 

A big labour but a major benefit.


Oh, and my Daughter named her "BESSIE", her serial number is 11253 and she is 95 years young. 




Wednesday, 24 August 2016

A Year Later





A year later. 

Too much to do, not enough time- same old excuses.  You could call the last year "R&D", you could call at least two months of last year "Moving Giant Machines Around and Digging Giant  Holes". You could also simply call it "Getting Ready". 

I  made a lot of things last year, so many of them worth uploading here, but I'm going to limit myself to showing five or six images of work, just to help get the old Blog show back on track.


three traditional, forge welded carpenters axes of various styles


Small jewelers raising hammer

Nano Carving axes








The real changes have been in the heavy equipment field. 

The first, resounding addition to my arsenal is my 1921 Massey 2 CWT (110kg) power hammer which I bought, stripped, rebuilt, restored and installed last summer.   Here is a photo of her in her freshly applied green (6002 emerald Green! ) warpaint. I will do a blog entry all about her very soon. Including a few videos of her throwing down. 





Needless to say, the metal moving capability of this beast is simply remarkable compared to my 30kg goliath spring hammer. I am now limited by the metal I can heat up and carry, rather than the size of stock I that my gear can handle.



So that takes care of the large end of the spectrum. I have also collected my first ever piece of NEW (except hand tools such as grinders etc..) equipment, this Anyang 25kg (55lb)








I bought this hammer to compliment my new "annex" workshop which houses our traditional solid fuel  forge and also provide a real delicate, finessed type of hammer blow (that is not to say the Massey is not controllable- you can really be very delicate with it if required)



This brings us on to the Coke forge itself, which has been a wonderful addition and so pleasant to use after years of standing next to gas furnaces. I was "brought up" on a solid fuel forge and having the use of  it really feels like coming home in a lot of ways. It was all fine and dandy until after only 10 weeks of use the forge fan, after only the slightest adjustment to the electrical "rheostat"  controls made a loud pop and caught fire. This lead to a 5 week wait on a replacement fan and after installing the new one, the rheostat doesn't work properly so I am stuck permanently on "half air", which for these fans is an awful lot, so my fuel consumption is rather high. these frustrations are sent to try us, I am sure. ...

My Dad using the Forge



You can't have a forge without an anvil! So here is my lovely 2cwt, wrought double bick. possibly made by Peter Wright but stamped "Birmingham" (manufacturers of all sorts of things used to sell on stock to distributers back then and mark them as they wished. it's possible that this anvil is a "second" and thus not stamped PW)  The stand was a nice bit of improve- a basic frame made up in steel then lined with scrap pallet wood and filled with concrete.  The base weighs around 150 kg and is totally stable. It is also ideal for fixing tool racks onto as you can fix straight into the concrete with rawl plugs and coach screws. After a few days use, enough iron scale had worked its way under the feet of the anvil to totally deaden the ring. Tidy.




Ive also picked up this nice vertical bandsaw  (which promptly caught on fire after it's second use, causing an all out panic as the "on-fire" parts were totally sealed away under a panel held on with  eight Allen key screws...) after the fire was dealt with (it was an electrical fault in the inverter) it sat, sulking in the corner for over a year awaiting me to organise and install replacement parts. Which I did!... eventually..




Since it's resurrection, I have been very pleased with its performance, and overall usefulness.

I also bought a large pedestal grinder which... promptly caught on fire! (old age, the motor was just fully burned out). The grinder is still sulking, or is it me that is sulking...? Anyway- anyone want a grinder?- it's cheap! )



Between re-organising my workshop, spending all of my money on century old cast iron and putting out electrical fires, I have also spent a good amount of time working with my friend and all round good egg Owen Bush on various exciting projects including this giant sword for this years "Arctic Fire"  as well as other things.




Thursday, 21 May 2015

Six Months Of Progress


Neglected for months, left abandoned without even a passing hello, this page has sat....

September to May is quite a pause- so Happy Halloween,  Xmas and new year, St valentines, Easter,  May Day and soon to-be Whitsun.

The flat reality has been that I have simply been too busy to maintain this page effectively so i will do a keep run-through over a handful of blog post to bring the page up-to-date with various projects and works I've engaged with since my last post.

With big changes a comin' to how I work,  I am also (AGAIN!!) re-affirm my promise to hold this page in a better state of maintenance with more regular postings.

In order to rattle through the last couple of months of work, I'm going to pick out a heap of pictures to post here today and then revisit the subjects in coming weeks to discuss them in greater detail.

Also, would just quickly like to thank HUNDREDS of you who drop in regularly to see if there’s anything new…. Sorry for the wait!



 Research trip to Ernest Wright and Sons scissor factory, Sheffield
 
Saddle grinders
 
Unfinished blanks

 
A proper furnace!
 




Decorated Forestry Axe






Experiments in Scandinavian socketed axes
 


Scissor and shear forging







Wrought Iron Bell Clappers



forestry and carving axe

 
Medieval carpenters axe



Hook Knife



Old dutch style trowel

 
Hand forged wrought iron left-handed Thumb-bow for tailors cutting shears. (More to come!)

 
Stone Mason's Toothed "axe"
 

5lb Jersey Pattern felling axe

Ripple Ash hafted camp axe
 
"swan neck" gouge
 


Wrought Iron and steel Hunter's Knife







Forging Tailors Shears- more pictures to come!

Photos by Anna Lucia Sadler